My portable ham radio setup for VHF and HF

Estimated reading time: 10 minutes

As outlined in my first post I simply love to operate battery powered in the great outdoors. Therefore it’s only natural to participate in the SOTA (Summits-On-The-Air) award program which requires setting up portable ham radio stations on the top of summits and conducting QSOs with fellow ham radio operators from there.

While getting QRV from any summit can be achieved with quite simple means I do realise the existence of an perceived entry barrier. In my opinion this is mostly due to a lack of searchable information concerning portable ham radio setups used by experienced operators. Unfortunately this is preventing newcomers from activating their first summit. As a result, not as many people as potentially could enjoy this fantastic aspect of ham radio. In this article I’ll be describing my portal ham radio setup used for both VHF and HF in order to give beginners a reference setup to expand upon.

My portable VHF setup

So what do you truly need for portable ham radio on VHF? A simple handheld radio such as the Yaesu FT-270R totally suffices:

Yaesu FT-270R 2m hand held radio

The FT-270R has an output power of 5W which is more than sufficient if you are operating from the top of a summit. While operating from OE/OO-080 „Sternstein“ on 2020/05/19 I managed a summit-to-summit QSO on 145.500 MHz with DL8MEK/P who was operating from DL/CG-095 „Seekopf“. The distance between those 2 summits is a whopping 154 km!

The great advantage of portable ham radio via VHF is that you just need to pack a hand held radio and off you go. Unless you forgot to charge it’s battery you can be sure that nothing will prevent you from getting QRV.

My portable HF setup

In order to get QRV on HF a bit more effort is needed. Here’s an overview over all the parts required for portable ham radio on HF:

Radio/Microphone

As a portable ham radio transceiver I’m relying on the Yaesu FT-817ND, a small and versatile multi-band (160 – 6m, 2m and 70cm), multi-mode (CW, AM, LSB, USB, FM, Data) transceiver with a output power of 5W. As a microphone I use the standard Yaesu MH-31A8J microphone.

FT-817ND portable ham radio transceiver
Yaesu FT-817ND + Yaesu MH-31A8J microphone

Power Source

As power source a LiFePo battery with 4 cells (4S) is used. It has a nominal voltage of 13.2 V (perfectly suited to supply the FT-817ND which preferred voltage is defined as 13.8 V ± 15%) and a capacity of 3100 mAh. On both lines (VBAT+ and VBAT-) connecting the battery with the radio I’ve placed 10A fuses to defuse (haha) the most inconvenient perils of short circuiting lithium based batteries. The battery is connected with the fuse cable via a EC3 plug/receptable pair. It ends in a Anderson PP15/30/45 power connector which in turn is connected to the FT-817ND.

4S LiFePo battery power source for portable ham radio
LiFePo (4S/3100 mAh) rechargeable battery as power source for portable ham radio

ATTENTION: Do not use LiPo batteries without any voltage reduction (e.g. diodes in VBAT line, linear voltage regulator, …). A fully charged LiPo battery has a cell voltage of ~4.2V. Hence a fully charged 4S LiPo battery has a VBAT of 16.8V! This voltage is high enough to damage your transceiver!

Antenna Mast

As antenna mast I’m using a 10 m GFK (fiberglass) telescopic mast available via SOTABEAMS. Because the elements get progressively thinner I’ve removed the top 3 elements to allow mounting a rather bulky balun. This reduces the effective height of the antenna to approximately 7 m which is still more than sufficient.

Collapsed and fully extended GFK antenna mast.

In order to securely mount the antenna mast I’m using expander ropes to fasten the mast to sturdy objects. A secure mount is absolutely necessary given that a antenna mast is basically a very long lever. Even just a small force exerted by the antenna wires at the top of the mast (= long side of the lever) is transformed into a large force at the base of the mast (= shorter side of the lever). This effect can easily upend your mast.

The extended GFK antenna mast mounted to a summit cross (incl. FT-817ND)

Antenna

For my actual antenna I use a home-built inverted V dipol triband antenna for 40/30/20m. Two antenna traps on each dipol ensure that each signal only „sees“ the optimal dipol length for its frequency. A portable HF antennas are a huge topic on its own. Hence I shall refrain from going more into detail here lest I blow the scope of this article.

Inverted V Dipol as portable ham radio antenna for HF
Inverted V Dipol 40/30/20m Dual-Band Antenna on top of OE/OO-248 „Wasserklotz“

The inverted V dipol antenna represents a balanced load but the coaxial feeding cable the antenna is a unbalanced source. Thus a balun converting the unbalanced signal to a balanced signal is necessary. For this purpose I am using a CG Antenna BL-01 1:1 BALUN. Mounted on the top of the antenna mast, it represents the tip of the inverted V dipol antenna. Note: This balun is rated for 100 W which is a bit of an overkill considering that the FT-817ND is only capable of delivering 5W.

CG Antenna BL-01 1:1 BALUN

For connecting the FT-817ND transceiver with the balun feeding the dipol antenna I’m employing a 10 m FTS-H 200 PVC coaxial cable with male SMA connectors on both ends. Both the radio and balun HF connectors are of type UHF female. An UHF Male/SMA Female adapter has been permanently connected to both radio and balun to allow easy connection.

10 m RPSMA Male/Male FTS-H 200 PVC Coax Cable

Update: Here’s a a more detailed article on my multi-band inverted-vee trapped dipole.

Transport Case

As transport case for all electronics parts I use a yellow B&W Type 1000 Outdoor Case. Although a bit heavy it allows for waterproof transportation of all the electronic parts.

Yellow B&W Type 1000 Outdoor Case containing all electronic portable ham radio equipment

As you’ve seen there’s rather a lot of equipment necessary for performing portable ham radio on the HF bands. If you forget one of these parts at home you won’t be able to radio. However, the increased radio range (due to skywave propagation) makes the additional complexity and weight well worth it.

Also, in order to achieve a valid activation you are required to have at least 4 valid QSOs. During weekdays it won’t always be possible to collect 4 QSOs on VHF only. Therefore lugging HF equipment up the summit is sometimes the only way to ensure a successful activation.




Leave a Reply

Your email address will not be published.


Comment


Name

Email

Url